50tech.com

... car, but do things change if the car has already been modded like mine? How do you know what fmu, injectors, fuel pump, timing, etc... I am only looking to add an entry level 5-6psi blower. It's not a race car by any means, but I try to go to the track a couple times a year. (PS, I posted this ...

... happens when its hot outside...if its cold, i could drive my car for hours on end...i need help, as this is getting frustrating, and people are looking at me when i drive by popping i have replaced all plugs, wires, cap and button last summer thanks frank

... for any signs or broken wires or wires chewed by critters and I am stumped. I am pretty familiar with Mustang wiring harnesses and I call myself looking at all the wiring. The only wiring I can find damaged is the plug that goes in the manual trans (reverse switch?) is charred from being unplugged ...

... i am currently running the crower 15511 but i am in the process of building a 347 with Eagle h-beam rods and some flat top Probe pistons. i am looking to stay with my Speed Density setup as long as i can so what do you guys think about my cam? Stick with it or is there another cam anybody ...

... convertible,withan AOD..and 3.27's gears...The car is bascilly stock except for a set of shorty headers,,Off H-pipe and a Flowmaster cat back..Im looking into the Kenne bell superchager the basic kit its the new 2.1 with 5-6 psi..I want to keep my stock injectors and MAF but im going to run a ...

... in the same boat as the Original Poster! Doing a HCI also with edelbrock rpm heads... trickflow intake and a comp xe264hr cam... and i have been looking for the damn answer CAN I RUN 24lb injectors with this set up and so far all i have gotten from many boards is the typical "GO MA, SD SUCKS!" ...

... 88 lx with a few mods look in sig, Well i want to do a heads and cam swap, I was thinking twisted wedge or gt40x what do you guys think, also was looking a a few SD friendly cams, which one will run the best with good power results, also looking to keeping stock fuel system, what do you guys think, ...

Been looking on ebay...think I'll go with a 76mm MAF, probably C&L, may need to up the fuel pressure, I'll let you know, thanks

Thanks for the help...I'm just now finding out (by looking at injectors and MAF sensors on ebay) that injectors and MAF's need to be somewhat matched. I pulled my MAF off and measured it at 55mm,and has a plug that sez F1ZF-12B579-AA, it's not on ...

... Cougar LS with an AOD, and the Standard Output 155hp 5.0 with Speed Density. I'm wondering what kind of performance upgrades I can look at, looking for good suggestions. I know that going to a true dual exhaust with at least the mustang headers is step one, but I'm in search of a shop that ...

I am looking to buy some Cobra R wheels 17x8 with 245/45/17 or 255/40/17 tires to put on an 86 Mustang GT with stock suspension. The car has the MAC cat back exhaust system and I currently have the stock 10 hole wheels with ...

Anyone want to offer up some first-hand experiences or opinions on APC Super Race Seats? Looking for anything on: comfort (for a daily driver), ease of installation, are they a direct replacement for stock seats? (or is modification required for mounting the seat ...

Hi, I am new to the site, and I need some help. I am looking for a speed density friendly cam. Here is my set up. P/P H.O. upper and lower intake P/P E7 heads Stock 5,000 mile H.O. bottom end 94/95 mustang fuel rails 19lb injectors 255lph intank ...

... the mustang h.o. specific order so i have to change the comp and cam at the same time, leaving me unable to use what i have now. anyways, im looking at a couple options. the trickflow stage 1 cam, a stock mustang cam, or something out of the comp cams lineup. keeping in mind that i have ...

The sway bars should produce the results you're looking for. I can't vouch for one brand over another.